|
Features: • Dual 4-digit LED displays of process and setpoint values
• User friendly menus and tactile keypad for easy programming
• One-touch autotuning for quick setup and precise control
• Includes Limit Alarm relay(s) with 8 programmable modes and adjustable deadband provides for dual control (heat and cool)
• Countdown timer for setting delay of alarm relay activation
• Single stage Ramp Soak and Auto/manual control modes
• Model 48VFL11 is UL, CSA and CE approved
• Complete with mounting brackets and screw terminals
Specifications:
Inputs:
-Type K -58 to 2498 °F (-50 to 1370 °C)
-Type J -58 to 1830 °F (-50 to 1000 °C)
-Type B 32 to 3272 °F ( 0 to 1800 °C)
-Type T -454 to 752 °F (-270 to 400 °C)
-Type E -58 to 1382 °F (-50 to 750 °C)
-Type R/Type S 32 to 3182 °F ( 0 to 1750 °C)
-Type N -58 to 2372 °F (-50 to 1300 °C)
-PT100Ω RTD -392 to 932 °F (-200 to 500 °C)
-DC current/DC voltage 4-20mA DC, Load <3 ohms/1-5 VDC
Output Relay: 5 Amps@ 110V, SPDT (resistive load)
DC Voltage: 24 VDC (pulsed) (drive for SSR)
DC Current: 4-20mA resistive. Impedance 600W or less
Alarm Relay: 48VTR 5 Amp @ 110V, SPST (resistive load) 96VTR
Accuracy: ± 0.2% FS + 1 digit
Temp. stability: 5μV / °C
Sampling Time: 0.25 Seconds
Display: 4 digit; Red LED (Process) Green LED (Setpoint)
LED Status: Control/Alarm, Manual mode, Autotune
Control Modes: Proportional Band: 0.0 to 100.0% (Autotuneable)
Integral Time: 0 to 3000 seconds (Autotuneable)
Derivative Time: 0 to 3000 seconds (Autotuneable)
Cycle time: 1 to 100 seconds
Anti-Reset: Inhibit integral action outside proportional band
Manual Reset: 0 to 100% of proportional band
Hysteresis : 0.0 to 25.5% of full scale
Front Panel: Lexan, Drip/Dust proof (IEC IP55 Standard)
Power Supply: 85 to 260 VAC, 50/60 Hz (6 watt)
Operating Temp: 14 to 122 °F (-10 to 50°C)
Panel cutout: 48VTR 1.77x1.77” (45x45mm)
96VTR 3.58x3.58” (91x91mm), 4” deep - Ordering Information:
Complete part number below with desired specifications.
Select either:
48VFL11 .....1/16 DIN PID Controller
96VFL11 .....1/4 DIN PID Controller
Then:
1 .......Thermocouple inputs (User selectable J,K,T,B,E,R,S,N)
R .......RTD Input (Pt 100 ohm)
A .......4-20mA Process inputs (Programmable to engineering units)
V .......1-5VDC Process inputs (Programmable to engineering units)
Then:
1......5 Amp at 110 VAC Relay control output
2......Pulsed 24 VDC control output
3......4-20 mA control output
404216 .......1/16 DIN NEMA-4X Cover
|
